10 Facts About Fiat Panda Key Fob Replacement That Will Instantly Put You In A Good Mood
Reasons Your Fiat 500 Key Fob Won't Work
A key fob for Fiat 500 makes it simple to open doors and start your car. However, there are numerous reasons why the key fob might stop working. This could be due to a dead battery and water damage, as well as problems with receiver modules, as well as interference.
This listing is for an NEW replacement Fiat Flip Key Remote - look-alike Ilco brand that needs to be professionally programmed by a local locksmith (click here for Locksmith Search). It comes with lock, unlock and trunk buttons.
Dead Coin Battery
A dead battery is the main cause of your 500 key fob being inoperative. Modern key fobs have a limited operating range, and must be within some feet of the car to operate. If you're far away from your vehicle, and you press the key fob button the car will not respond, and will display the "Key Fob Not Detected" message in the instrument cluster.
If this happens then replace the battery for your coin-cell (Part Number CR2032) by a fresh one of a reputable brand like Panasonic Duracell or Energizer. They can be found in your local hardware store, or online.
After you've replaced the coin cell battery you can test it by standing near your Fiat 500 and pressing the buttons. The parking lights should light up and the key fob will operate the lock and unlock switches.
If your key fob isn't working after replacing the battery, it could be water damage that prevents it from connecting to the module inside your vehicle. Water damage can happen in many ways, including a simple splash or submerging the key fob into saltwater at the beach. If you suspect that your fob was exposed to water, place it in a rice bag to draw out the moisture. If this doesn't work your fob may need to be reprogrammed by a professional auto locksmith or the dealer.
Water Damage
Although the fob is equipped with rubber seals to keep water from the chip's electronic circuit, submerging it in the ocean or washing it in a machine can cause water damage. Saltwater can cause the circuit board to short and then cease to function. It's not good to submerge the fob in water however, but don't give it up in the event that you accidentally drop it in water or forget to take it out of your pants pocket.
First remove the battery from the fob. Before replacing the battery, clean the electronic chip with isopropyl or similar products. Then, test the fob to test if it works. If the key does not function, it may have to be reprogrammed. This is usually handled by an auto locksmith or dealer.
If the key you have is older and not programmed to work with your vehicle then you'll need to replace it completely. A professional locksmith in the automotive industry can do this job. The locksmith needs to cut the key to match the ignition in your vehicle. They will also need to reprogram the fob in the car's system. It's a simple and cost-effective process that is usually completed the same day.
Receiver Module Issues
One of the most common reasons why your 500 key fob may stop working is because it's out of range. The remote usually has an operating range of 30 feet or less, and if it's too far from your car, it will not respond to your commands. This can be fixed by moving closer to your vehicle until it starts responding.
If your fob doesn't work after replacing the battery for the coin, also known as a "button", "watch" or "button", it may be due to a malfunction on the internal circuit board. Reprogramming the fob typically resolves this problem. You can find the steps for most vehicles on YouTube or in the owner's guide.
It is possible to replace the clips made of metal that hold the coin batteries in place. If fiat key replacement near me could hinder the coin battery from sitting properly and cause your remote to malfunction.
In rare cases the fob may be out of the vehicle's sync because of hardware or software problems. This could be a huge problem, but you can frequently fix this issue by visiting a local dealer or auto locksmith to reprogram your fob. In some instances, they may need to reinstall the software on your body control module too.
Interference
Interference can also cause the key fob not to receive or transmit an signal. This can happen when the key fob is close to a radio transmitter (cell phones or radar detectors) or another source of electromagnetic radiation. Other reasons why the key fob might not work could be due to a weak connection to the buttons and internal chip, or water damage.
If the key fob has been unable to function for a while out of the blue or after trying every option at home to solve it e.g. You might have a damaged 500 receiver module after you've tried replacing the battery, reprogramming or using an alternative key fob. The receiver module, located beneath the dashboard, picks up radio frequency signals from your key fob. It converts the signals into electronic commands that are then read by the vehicle.
Fortunately, there's an easy method to reset all on-board systems in your 500 and include the key fob. Disconnect the battery 12 volt for about 15 minutes, by removing the negative cable and then the positive cable. Reconnect the battery. This will get rid of any remaining electrical charge and restart the car's computers. This could help the key fob to function again. If the issue continues, you should speak with an expert technician. They will be able to identify the root cause of your issue.